做任何事都應該有一定的細節規范，因為我們都知道細節決定成敗，我們一定要做好細節工作，鑄石板的施工也一樣，我們應該做好哪些細節規范呢，接下來為大家詳細說明下： 鑄石板規格為200×300×20mm，為確保施工質量梯形板需要根據實際施工需要進行現場切割。施工時為確保使用面平整度達標，需要用木錘或橡皮錘敲打鑄石板。施工時，其表面的雜物、灰塵、油污等在襯砌鑄石板前清掃干凈。打上調制好的膠泥進行襯砌施工，鑄石板上涂抹的膠泥層厚度以8-10mm為宜，鑄石板間的膠泥以3-5mm為宜，膠泥層和鑄石板間的接縫必須充填飽滿，不得有空洞。 將調制好的膠泥先涂抹在鑄石板上，然后將帶有膠泥的鑄石板貼在施工基面上并用力擠壓，必要時還要用皮錘敲擊以增加其牢固度。要求施工溫度在0℃以上，相對濕度不大于80%，膠泥的調制量以40分鐘能用完為宜。